Products
-
Elpress products
-
Pre-insulated terminals
- Ring terminals 0.1 - 6 mm²
- Fork terminals 0.1 - 6 mm²
- Flanged fork terminals 0.5 - 2.5 mm²
- Hook terminals 0.5 - 2.5 mm²
- Pin terminals 0.1 - 6 mm²
- Blade terminals 0.25 - 6 mm²
- Through connectors 0.25 - 6 mm²
- Through connectors with heat shrink insulation 0.5 - 6 mm²
- Parallel through connectors 0.5 - 6 mm²
- Receptacles, rolled type 0.1 - 6 mm²
- Multiple tabs, rolled type (piggy back) 0.5 - 2.5 mm²
- Receptacles fully insulated rolled type 0.5 - 6 mm²
- Tabs 0.5 - 6 mm²
- End connector sleeves fully insulated 1 - 6 mm²
- Bullet 0.25 - 6 mm²
- End connector sleeves fully insulated 0.25 - 6 mm²
-
End sleeves
- Pre-insulated end terminals 0.14 - 50 mm² ET, standard colour
- Pre-insulated end terminals 0.14 - 50 mm² ETT, alternative colour
- Pre-insulated end terminals 0.14 - 50 mm² ETD, alternative colour
- Uninsulated end terminals 0.25 - 50 mm²
- Pre-insulated TWIN-end terminals 2 x 0.5 - 2 x 10 mm², ET2, standard colour code
- Pre-insulated TWIN-end terminals 2 x 0.5 - 2 x 10 mm², ETT2, alternative colour code
- Pre-insulated TWIN-end terminals 2 x 0.5 - 2 x 10 mm², ETW2, alternative colour code
-
Un-insulated terminals
- Ring terminal 0.25 - 6 mm²
- Fork terminals 0.25 - 10 mm²
- Pin terminals 0.25 - 6 mm²
- Jointing sleeves 0.75 - 10 mm²
- Receptacles rolled type 0.5 - 6 mm²
- Receptacles with locking lip rolled type 0.5 - 6 mm²
- Multiple tabs, rolled type (piggy back) 0.5 - 2.5 mm²
- Receptacles 90° rolled type 0.5 - 1.5 mm²
- Receptacle angled rolled type 0.5 - 1 mm²
- Tab 0.5 - 2.5 mm²
- Tab with locking lip 0.5 - 6 mm²
- Bullet and Socket 0.2 - 1.5 mm²
- Tab connectors
- Tab connector 45°
- Tab connector 90°
- Tab connector 2 x 45°
- Connector block for receptacles 1.5 - 6 mm²
- Connector block for bullets and sockets 0.2 - 1.5 mm²
- Connector block for receptacles - 400V/18A
- Tabs 1, 2 and 3 male
- Insulation boots
- Tabs for soldering
- Assortment boxes
-
Cu terminals
- Tube terminals 0.75 - 10 mm²
- KRF tube terminals 16 - 800 mm²
- KRF tube terminals with two holes, 16 - 400 mm²
- KRFS tube terminals 50 - 400 mm² with narrow palm
- KRFN tube terminals 50 - 240 mm² with narrow palm
- KRF angled terminals 45°, 10 - 150 mm²
- KRF angled terminals 90°, 10 - 150 mm²
- KRD tube terminals 16 - 1000 mm²
- KRT tube terminals 10 - 500 mm²
- DIN 46235 tube terminals 10 - 1000 mm²
- DIN 46234 sheet metal terminals 10 - 185 mm²
- KS/KSF through connectors 0.75 - 800 mm²
- KS/KSF through connectors with partition 10-500 mm²
- KSxP parallel connectors for conductors total 0.5 - 6.75 mm²
- KSxP parallel connectors for conductors total 10 - 630 mm²
- CUT through connectors for single strand conductors 6 - 16 mm²
- KSD through connectors with partition 16-1000 mm²
- KST through connectors with partition 10-500 mm²
- DIN 46230 pin terminals 10 - 95 mm²
- KRX tube terminals for Excel and Fxcel cable 10 - 16 mm²
- KSX through connectors for Excel and Fxcel cable 10 - 16 mm²
- Al terminals
- AlCu terminals
- C sleeves
- Overhead line connectors
- Screw connectors
- Cable joint and terminal
- Crimping tools
- Cutting and stripping tools
- Deep earthing
- Earth braids
- Cable clamps
-
Pre-insulated terminals
- System Elpress
Knowledge provides quality
Properly trained personnel ensure the quality of products and services. The training certificates serve as a quality document between you and your customer.
Who do we train, and how?
Each course has a level suitable for everyone; operators, designers, supervisors and quality managers. In addition, there is a possibility to tailor the course so that the content suits the needs in the company. You also decide if the course will be held at the company or in Elpress’ training facilities.
We mainly address four target groups:
- Electric plant staff/Installers
- Transformer manufacturers
- Traction / Train manufactures
- Wind power manufacturers
CONTACT
Liselotte Hellgren-Wågström
academy@elpress.se
